Free worldwide shipping on bulk orders over $199

Category: Printing Tips

  • How to dial in high-speed PLA for clean, fast prints

    How to dial in high-speed PLA for clean, fast prints

    High-speed PLA lets modern printers run far faster than standard profiles, but speed only pays off when walls stay clean and layers bond well. A few structured checks will get you there faster than trial and error.

    Start with temperature

    Faster printing means the filament spends less time in the hot end. Most high-speed PLA needs to run 10–20 °C hotter than a standard profile. Print a temperature tower at your target speed, not at a slow calibration speed.

    • Begin around 220 °C and step up in 5 °C increments
    • Look for glossy, fully fused walls without stringing
    • Keep the bed at 55–60 °C for consistent first layers

    Match flow to your hot end

    Every hot end has a maximum volumetric flow. If you exceed it, extrusion becomes thin and walls lose strength. Run a flow test and set your slicer limit slightly below the point where under-extrusion starts.

    Cool hard, but evenly

    High-speed PLA relies on strong part cooling to hold overhangs and fine detail. Use full fan speed after the first layers and check that airflow reaches both sides of the nozzle.

    Once these three variables are dialled in, save the profile and reuse it across colors from the same LANDU high-speed PLA range for consistent results.

  • Keep filament dry and ready to print

    Keep filament dry and ready to print

    Most filaments absorb moisture from the air. Wet filament causes popping, stringing, rough surfaces and weaker parts. A simple routine keeps every spool ready to print.

    Know the signs of wet filament

    Listen for crackling at the nozzle and look for fine bubbles or a fuzzy surface finish. Nylon, TPU and PETG show these symptoms first, but PLA is affected too over time.

    Dry before you print

    A dedicated filament dryer gives the most consistent results because it controls temperature and airflow.

    • PLA: around 50 °C for 4–6 hours
    • PETG: around 65 °C for 4–6 hours
    • TPU and nylon: follow the material data sheet

    Store sealed between jobs

    Return spools to resealable bags or boxes with fresh desiccant. For materials you use daily, feeding directly from a dryer is the simplest option.

    LANDU dryers are designed around this workflow, so you can dry, store and print from the same unit.

  • Your first resin print: prepare, print, finish

    Your first resin print: prepare, print, finish

    Resin printing has a few more steps than filament printing, but each one is simple. Following the same workflow every time gives you reliable, repeatable results.

    Prepare

    Shake the resin bottle well, level the build plate and check the vat film for damage. Wear nitrile gloves and work in a ventilated space.

    Print

    Start with the exposure settings recommended for your resin and printer, then fine-tune with a calibration print.

    • Keep the room between 20 and 30 °C
    • Avoid over-filling the vat
    • Let the first layers bond fully

    Finish

    Wash parts in IPA or a recommended cleaner, let them dry, then post-cure under UV light. Remove supports before or after curing depending on how brittle the material is.

    Keep notes on settings and results for each resin. They will save you time on every future print.

  • Storing resin safely between prints

    Storing resin safely between prints

    Resin stays usable for a long time when stored correctly. Good storage habits also keep your workspace clean and safe.

    Keep resin away from light and heat

    Store bottles closed, upright and out of direct sunlight, ideally between 15 and 25 °C.

    Look after the vat

    For short breaks, cover the vat to block light and dust. For longer breaks, filter resin back into its bottle.

    • Filter through a fine mesh funnel
    • Remove cured fragments from the film
    • Label bottles with the date opened

    Handle waste responsibly

    Cure leftover resin and contaminated wipes under UV before disposal, following local regulations.

    Always check the safety data sheet for the specific LANDU resin you use.